Painting your ceiling can be daunting, but it doesn’t have to be. With the help of the right commercial painter in Melbourne and proper preparation and knowledge, you’ll be able to get the job done quickly and effectively. Here we have discussed the essential steps to consider before painting your ceiling. But before starting with the steps, let’s learn –
Types of Ceiling Paint
1. Flat Acrylic Ceiling Paint
According to plastering service experts in Melbourne, flat acrylic ceiling paint is best used in low-humidity areas like bedrooms and living rooms. Since most ceilings are flat, flat paint only reflects a little light.
2. Satin Acrylic Ceiling Paint
Flat paint is more likely to discolour, fracture, or chip in rooms with greater humidity levels. Because of this, satin sheen ceiling paint is preferable for ceilings in bathrooms, laundry rooms, and other more humid areas.
3. Semi-Gloss Acrylic Ceiling Paint
Semi-gloss ceiling paint is best suited for ceilings directly above a shower stall or any other area prone to constant humidity, as it is least likely to crack in humid environments.
Steps to Paint Ceiling
1. Prepare Room
The best house painters in Melbourne say that any space needs to be prepared before you start the painting project to avoid mishaps. You need to prime the room by doing the following things:
- Remove all the furniture from the room (if feasible) to prevent splatters on what may be a treasured artefact handed down through the years.
- Before you begin, ensure the ceiling is free of dust and debris. Keep in mind that paint won’t adhere well to a dirty ceiling.
- Look for cracks and holes in the ceiling and patch them if you discover any.
- Ensure all ceiling fittings, including light fixtures and smoke detectors, are taken down. Put all the hardware inside a polythene bag.
2. Protect Surfaces
Your walls, doors, or windows must not be harmed while painting your ceiling. It would help if you took the following actions to make sure that all of your surfaces are shielded:
- Hang drop cloths to cover all the vertical surfaces if you’re painting your ceiling after you’ve completed painting the walls. Use the same strategy for your doors and windows, and add painter’s tape to keep them in place.
- Drop clothes over the floor and any furniture too large to be moved.
- If you’re merely painting the ceiling of a room, place a 2-inch strip of painter’s tape over the top of the walls to protect them from roller marks.
3. Apply Primer
Primer will cover any stains on your ceiling. When applying primer, the best house painters in Melbourne recommend bearing the following in mind:
- Allow the primer to dry as directed thoroughly.
- Use a paintbrush to paint all the sharp edges where the ceiling meets the wall before beginning to paint the ceiling with a roller. By doing this, you can be certain the paint will fill any gaps the roller could leave.
- After that, you should use an angled brush and primer to cut in the borders of the ceiling. Next, apply the remaining primer in a thin layer and wait until it has dried thoroughly.
Must Read: https://ramneeksidhu.co.uk/ultimate-kitchen-design/
4. Paint Sections
The plastering service experts in Melbourne say the ideal method for painting a ceiling is not to use a paintbrush but a paint roller and work in areas 3 feet by 3 feet (essentially, to keep track of what you’ve painted). The following commercial painter in Melbourne’s advice will be helpful to you at this stage of the procedure:
- Start each new piece by overlapping into the damp edges of the one before it to prevent lasting roller markings.
- Painting over wet borders enables portions to be blended easily.
- Fill the roller with paint using the paint tray, then roll gently and evenly.
- Roll in slightly different directions; a completely straight roll could leave overlap traces.
- Keep rolling out the paint until the ceiling painting finishes, and mix it with the cut-in edge and the preceding section.
- Use a low nap roller for smooth ceilings. Use a roller with a 1/2-inch or 3/4-inch nap for a textured ceiling.
5. Apply the Second Coat
If you’re painting your ceiling a vivid colour, a commercial painter in Melbourne recommends applying a second layer. What you should remember is this:
- Before applying the second layer, give the paint time to dry completely.
- Apply the second layer swiftly and in one direction, covering the whole surface.
- Start cleaning up just after all of the painting gets completed.
- Put all your tools, including brushes and rollers, into a big tub for cleaning.
- Remove all of the painter’s tape when the paint is touchably dry.
To Conclude,
Before beginning any painting project, it’s essential to research beforehand to know exactly what tools and materials you’ll need for the job at hand—like when preparing to paint your ceiling! By following these tips from commercial painters in Melbourne and doing some essential preparation beforehand, you’ll be well on your way towards creating an even-looking painted surface on your ceiling without any unwanted drips or splatters along the way!
Also Read: https://ramneeksidhu.co.uk/5-reasons-to-pressure-wash-the-roof-of-your-home/